How to Properly Install Clipper Blades on Andis Tools

By Patricia D. Johnson — Updated: November 2026

How to Properly Install Clipper Blades on Andis Clippers

How to properly install clipper blades on Andis clippers at home

Quick answer: Check your blade type before you start working. Detachable blades slide onto the open hinge first. Turn the clipper on, then snap them shut. Adjustable blades sit on screws and need careful alignment. Finish every install with fresh clipper oil.

Cutting hair like a pro starts with your tools. If your blade is loose, your haircut will look messy. You might even pull the hair or nick the skin. Knowing how to properly install clipper blades on Andis tools matters most. It is the first step to a perfect fade.

It can feel scary to take your clippers apart. You do not want to break an expensive machine. But you really do not need to worry. This guide makes the whole job simple.

You will learn how to snap on blades and how to screw them in. We will talk about two main types of Andis clippers. These are “Detachable” blades and “Adjustable” blades. Our guide on how to oil clipper blades covers the finishing step. By the end of this guide, you will feel like a master mechanic.

Andis Excel 5-speed clipper beside an Andis Master clipper

Contents

Tools & Prerequisites

Before you start, gather all your supplies first. Working on a clean table is best. You do not want to lose small screws in a thick carpet. Our how to clean hair clipper blades guide covers prep cleaning.

Essential Tool List

  • Your Andis Clippers: The power must be off.
  • Replacement Blades: Make sure they are the right size for your model.
  • Screwdriver: Usually a small Phillips head for adjustable models.
  • Clipper Oil: To keep the metal moving smoothly.
  • A Small Brush: To clean out old hair.
  • A Soft Cloth: To wipe away grease.

Comparing Blade Types

Blade Type Used On How it Attaches Difficulty
Detachable AG, BGR, SMC Models Snaps onto a hinge Very Easy
Adjustable Master, Fade, Envy Held by two screws Medium

Screwdriver, clipper oil, and cleaning brush laid out flat

How to Properly Install Clipper Blades on Andis: Detachable Blades

Detachable blades are the easiest to handle overall. They use a simple metal hinge system. Most professional animal groomers and barbers use these.

Step 1: Open the Hinge

Locate the metal flap on the back of the clipper. This flap is the hinge assembly itself. If it is closed, use your thumb to pry it up.

Step 2: Slide the Blade On

Hold the blade with the teeth facing away from you. Slide the metal slot of the blade onto the hinge. It should feel snug but not forced.

Step 3: Power On the Clipper

Turn the clipper ON before you snap the blade down. This is a simple secret pro trick. It helps the drive lever line up with the blade.

Pro tip: never snap a detachable blade down while the clipper is OFF. It can bend the small plastic parts inside. Always power on first during this step.

Step 4: Snap it Shut

While the motor is humming, press the blade down toward the clipper body. You will hear a loud, clear click. That click means the blade is locked.

A thumb pressing an Andis blade onto the clipper hinge

How to Properly Install Clipper Blades on Andis: Adjustable Blades

These blades stay on the clipper all the time. You only take them off to clean or replace them. This process takes a bit more focus.

Step 1: Remove the Old Screws

Use your screwdriver to turn the two screws to the left. Set the screws in a bowl so they don’t roll away. Then lift the old blades off carefully.

Step 2: Clean the “Yoke”

Under the blades, you will see a plastic piece that moves back and forth. This moving plastic piece is the yoke. Brush out all the tiny hairs trapped here.

Step 3: Place the Small Blade

The cutter is the smaller blade here. Place it flat on the plastic yoke. It should sit flat and move freely side-to-side.

Step 4: Place the Large Blade

Put the big “Comb” blade over the small one. Line up the two screw holes carefully. Start the screws with your fingers first.

An Andis Master clipper with blades removed, seen from above

Step 5: Align the Teeth

This alignment is the most important part. Do not tighten the screws all the way yet. Look at the teeth from the side.

The small blade teeth must be slightly below the big blade teeth. If the small teeth stick out further, you will cut the skin. Keep both blades straight and perfectly parallel. Our how to adjust Andis trimmer blade guide explains fine alignment.

Step 6: Tighten Down

Once the blades are straight, tighten the screws firmly. Check the alignment one last time after tightening. Firm screws hold the alignment during cutting.

Expert Tips & Troubleshooting

Even experienced pros make mistakes sometimes too. If your clipper sounds like a lawnmower, something is wrong. Here is how to fix common issues.

The “Loud Rattle” Fix

If the clipper is very loud, the blade might not be snapped all the way. For detachable blades, pop it off and try again. For adjustable blades, check if the screws are loose.

Dealing with “Dead” Blades

Sometimes you install a new blade and it still won’t cut. This usually means the tension is wrong. Our guide on how do you sharpen clipper blades covers truly dull sets.

Diagram of correct and incorrect blade gaps

Proper Oiling Habits

You must oil your blades every single time you use them. This prevents heat and friction damage daily. See how to oil a trimmer for the full routine.

Follow these five oiling steps every time. Three drops cross the teeth during oiling. One drop protects each back rail too.

  • Turn the clipper on.
  • Put three drops of oil across the teeth.
  • Put one drop on each back rail.
  • Let it run for ten seconds.
  • Wipe off the extra oil with a cloth.

Critical warning: never use WD-40 or vegetable oil. Only use clear clipper oil on blades. Other oils will gum up the motor and ruin your tool.

A person holding a clipper sideways to oil the blade rails

Problem Likely Cause Simple Fix
Loud rattle while cutting Blade not fully snapped or loose screws Re-snap the blade or tighten both screws
New blade still won’t cut Tension or seating is wrong Re-seat the blade and check the drive lever
Blades get very hot Friction from too little oil Add clipper oil or use a coolant spray

Most install problems trace back to seating or oil. Work through the table before replacing any parts. The official Andis site lists model manuals and support.

Frequently Asked Questions

Why won’t my blade snap into place?

First, check the hinge for trapped hair. Hair might be stuck inside the metal fold. Use a brush or a toothpick to clear it out. Make sure the hinge is flipped up first. Then slide the blade on and snap again.

How often should I replace my Andis blades?

Blades can last six months to a year. That range suits people cutting only their own hair. If they start pulling hair instead of cutting it, they are dull. You can have them sharpened or buy new ones. Our guide on how long do Andis trimmer blades last explains more.

Can I put Andis blades on Oster clippers?

Yes, most A5 style detachable blades are universal. Andis, Oster, and Wahl blades often fit on the same hinge systems. Check your hinge shape before mixing brands.

My blades are getting very hot. What do I do?

Heat almost always comes from friction alone. This usually means you need more oil. You can also use a coolant spray. Stop cutting and spray the blades well. Wait one minute, then wipe and continue.

How do I prevent rust on my blades?

Rust is the true enemy of steel. Never leave your blades wet after cleaning. If you use a liquid cleaner, dry the blades completely afterward. Always finish with a light coat of oil to seal out moisture.

A rusted blade beside a shiny, well-oiled blade

Conclusion: How to Properly Install Clipper Blades on Andis

You now have the skills to maintain your equipment. Knowing how to properly install clipper blades on Andis tools saves time and money. You won’t have to pay a repair shop for a two-minute job. Keep practicing this simple routine at home.

Remember to keep your work area clean. Always turn the clipper on before snapping detachable blades. Most importantly, never skip the oil step. Your hands will get faster at this. Soon, you will be able to swap blades in seconds without even thinking about it.

Leave a Comment